Decopox Micro Mortar Color: NCS 1040R

PREPARATION OF THE SUPPORT

- The concrete supports must be solid, dry (fully set if they are newly built 28 days), level, absorbent, not contaminated with oils, detergents, powders or other substances.

- Evaluate the most convenient type of mechanical preparation (using an abrasive machine, polishing machine, hydro-cleaner ...) and apply one pass of Transparent Paviplast Epoxy.
- Oily surfaces have to be thoroughly devastated and treated, with Pavex 2C Primer + quartz already mixed or by dusting until saturated on the fresh product.

- On non-absorbent backgrounds (ceramic, marble ...), devastate, sand and vacuum, then apply one pass with Ecopox Plus 3C.
- On bases without guarantees of stability, create an effort, adding a fiberglass mesh to the system.

IMPORTANT
- For shades of yellow, orange or some reds, additional layers may be needed to obtain a good coverage (in some cases a first pass in white is recommended).
- Different production batches of the same color may have small differences, so it is recommended to use material from a single production batch.

- Some colors based on organic pigments (reds, blues, greens and intense yellows) tend to fade when they are subject to abrasion (either dry or wet).

In these cases it is advisable to protect the color with a clear finish pass

HOW TO USE

Mix the components A + B with a whisk at low revolutions for at least 1 minute, until obtaining a perfect homogenization.

APPLICATION

- Pour the contents of part B over part A, shake and mix with a low speed mixer. Add dilution water and continue mixing until a completely homogenized mixture is achieved, apply at a consumption per layer of 500 - 600 g / m2.

- To color the formulation, universal water-based pigment must be added, which has good compatibility within the system.

- The amount of pigment with respect to component A + B can vary between 1 to 10% depending on the color effect to be obtained.

- Decopox Spatula, can be used to obtain decorative floorings with various effects, for this type of application consult the indicative cycles or request the technical assistance service.

Optimal adhesion to concrete, tiles, resin coating.
- Steam permeable.
- Good resistance to wear.
- Ideal for making decorative effects.
- Flooring, apartments, offices, industrial ...
- Repair and restoration of floors.
- Indoor

BENEFITS

- Specific weight (25ºC): 2.00 ± -0.05 g / ml
- Viscosity Mp (25ºC): 5,000 ± -1,000 (spindle 2, rpm 5)
- Compression load: 35 N / mm2
7 days of curing and 50% RH)
- Flash point:> 100ºC
- Moisture in the support: 0%
* These results are from standard tests and may vary depending on the on-site conditions.

TECHNICAL DATA

Application temperatures 15ºC-30ºC and RH <75%
Consumption 500 - 600 g / m2 (1 layer)
Neutral Color
Dosage (A + B) Weight: A = 100 - B = 11 Volume: A = 100 - B = 20
Pot-life (50% RH) 5ºC:> 60 min 25ºC:> 40 min 35ºC:> 25 min
Dry to touch (50% RH) 15ºC: 14-18 hours 25ºC: 5-7 hours 35ºC: 3-5 hours
Pedestrian traffic (50% RH)> 18 hours (25ºC)
Repainting (50% RH) 18-36 hours (25ºC)
Hardening in
depth> 7 days (25ºC and 50% RH)

Cleaning tool Water
Conservation 12 months in original closed container (5-35ºC), sheltered from
weather and humidity
Maintenance and cleaning With neutral detergents