Standard putty for interiors

RENEWAL PUTTY

Indoor use

- Excellent workability (easy sanding)
- Does not drop / Great hiding power
- Excellent adherence
- Easily sandable
- Great smoothing capacity
- On absorbent funds
- Without fissures

APPLICATIONS /

- Indoor putty for multipurpose use, suitable for filling and smoothing cracks, cavities, gaps, etc.
- Especially indicated for renovation and / or cleaning of walls, leveling of supports, and smoothing of walls with defects (scratches, cracks, knocks, chipping, holes, etc.).
- Especially suitable for regularizing walls to the gotéele.
- Allows smoothing in a thin layer, leaving a smooth and white finish, so it can be left as a finishing coat before
to paint.
- Great ease of subsequent sanding leaving a completely fine and homogeneous appearance.
- Indoors.

SUPPORTS SUPPORTED /
- Cementitious, plaster, plaster with imperfections, gotée.

OBSERVATIONS /
- The support will be free of saltpeter, fungi ...
- Do not add water when the mass begins the setting process.

- When a second coat needs to be applied, apply before the first coat has set.
- Do not apply in a permanent state of heat, since the product could lose its benefits.

RECOMMENDATIONS FOR APPLICATION /
- Application temperatures between 8 - 30ºC.
- Do not incorporate any product into the mortar.
- The application of the product on brittle paints, old plasters ... that may come off with the application of putty is not recommended
- Do not apply on non-absorbent funds.

EXECUTION CONDITIONS /

- The support must be healthy, clean and free of moisture. If the support is somewhat friable or brittle, it must be consolidated with F-300 (1: 2 in water). In the same way, old substrates made up of dead plaster or poorly adhered parts must be repaired: restoring fatigued substrates without prior remediation is totally inadvisable.

- The supports must be healthy, stable and resistant, free of dust, plaster, paint ...

- Eliminate the deteriorated and degraded parts, until reaching the solid, resistant and absorbent support.

- Powdery surfaces must be consolidated with F-300.

- On surfaces without absorption, very smooth or little absorbent, strip and open pore to ensure good adherence.

HOW TO USE/
Mix a bag of Renovation Putty, (15kg) with 4 - 4.5 liters of clean water until
get a homogeneous mass and without lumps.

- Use the product within its useful life,
after this time, I could lose my
initial benefits.

- The smoothing operation is always carried out vertically from the bottom up with a wide trowel, adding material and removing the excess, trying to smooth and cover all surface defects.

- Splices are made on the contrary, from top to bottom.

- When the material dries, it is sanded and then another coat of plaster will be applied
horizontally from right to left, taking the joints from left to right. Finally, after drying this second coat, the surface is sanded and, if no imperfections are observed, painting is carried out when necessary.

EMPLOYMENT CHARACTERISTICS /

- Mixing water: 35%
- Rest time after kneading: 1min.
- Life of the dough: 5 h. (20ºC)
- Workability: 60min.
- Minimum thickness: 0-2 mm.
- Drying: 2 hours
- Repainting: 4 hours after humidity control
<4%.
- Yield: 1.47 Kg / m2 mm.
* These times can vary considerably depending on the ambient temperature.

BENEFITS /
- Apparent density in powder: 0.875 g / cm3
- Mass density: 1,270 g / cm3
- Mixing water: 35%
- Adherence:
• On Cement: 0.80 MPa
• On Ceramic: 0.29 MPa
• On Wood: 0.17 MPa
• Over Pladur: 0.10 MPa

* These results have been obtained under standard conditions and may vary depending on the installation.

CONSERVATION/
12 months from the date of manufacture, in the original closed container, sheltered from the
weather and humidity.