Wall and floor kit Micromortar Micropol 3C

€938.00

Rate it

Ask a question (0)

Product customization

Don't forget to save your customization to be able to add to cart

Kits

20 m2
60 m2
6 m2

Quantity

Two- component micro mortar (A + B) with water-based aliphatic polyurethane resins.

This decoratio polyurethane mortar is a two-component, water-based product designed for decorations on resin coatings, both for interiors and exteriors.

Ideal for renovation as continuous coating of swimming pools on tile

Colors: RAL LETTER on request

Coating with "spatulate" effect for exterior surfaces.
Pavements and coatings in light colors.
Great adherence on resin coatings.
Does not yellow.
Excellent mechanical resistance.
Abrasion high resistance.
Excellent resistance to UV rays and atmospheric agents.
Indoors and outdoors

Products that make up the kit

6 m² KIT
	one	1 Lt.	F300
	one	5 Kg.	FIBERED THICK MICROPOL
	one	5 Kg.	FINE MICROPOL
	one	1 Kg.	VELADURA
	Total weight	12 kg

20 m² KIT

	two	1 Lt.	F300
	one	25 Kg.	FIBERED THICK MICROPOL
	one	25 kg	FINE MICROPOL
	two	1 kg	VELADURA
	Total weight	52 Kg

KIT of 60 m²

	one	5 Lt.	F300
	3	25 Kg.	FIBERED THICK MICROPOL
	3	25 kg	FINE MICROPOL
	two	10 kg	VELADURA
	Total weight	175 Kg

KIT of 120 m²

	two	5 Lt.	F300
	6	25 Kg.	FIBERED THICK MICROPOL
	6	25 kg	FINE MICROPOL
	4	10 kg	VELADURA
	Total weight	350 Kg

Application and method of use of Micropol 3C

Mix the components A + B with a whisk at low revolutions for at least 1 minute, until obtaining a perfect homogenization. The application can be carried out with a steel trowel, rubber ... Prepare the mixture of the 2 components (A + B) pour the content of component B into the container of component A, stir the mixture and homogenize with the drill at low revolutions . Apply the product with the appropriate trowel at an approximate consumption of 450 - 550 g / m² per coat. To color the product use water-based dyes, the amount of dye with respect to the product (A + B) can vary from 3% to 10%, depending on the desired color effect.

Uses of the product Micropol 3C

Coating with "spatulate" effect for exterior surfaces.
Pavements and coatings in light colors.

Information about the stand for Micropol 23

The support must have a minimum mechanical resistance to compression of 25 N / mm2 and tensile strength of 1.5 N / mm2. The concrete supports must be solid, dry, level, absorbent, not contaminated with oils, detergents, powders or other substances.

On new setting concrete> 28 days.
Evaluate the most convenient type of mechanical preparation (using an abrasive machine, polishing machine or hydro-cleaner) and apply one pass of Transparent Paviplast Epoxy.

Performance of the Micropol 3C mortar
- Specific gravity (25ºC): 180+ / -0.05g / ml.
- Viscosity (25ºC): thixotropic paste.
- Dry residue: 84.3% by weight and 50% RH.
* These results are from standard tests and may vary depending on the on-site conditions.

Important information for the product Micropol 3C

Colors with shades of yellow, orange or red may require more applications to achieve a good coating effect (in some cases a first recovery of white is recommended). Multiple production batches may have slight color differences: If possible, use material from a single production batch. Some organic pigment-based colors (reds, blues, greens, and deep yellows) tend to fade when subjected to abrasion (either dry or wet). In these cases it is advisable to protect the color with a pass of transparent Paviplast Transparent finish.